So I came up with an idea to make my own tenugui.
Tenugui are the small hand towels used as head covering in kendo.
I had an unopened gocco printer lying around that I purchased in 2007 and decided it was high time to dust off the box and break open the packaging.
RISO Print Gocco’s are miniature printing presses first invented in 1977 by Noboru Hayama. It uses mini screen meshes coated with an impermeable material. When the screen is placed on a carbon ink containing original (like a photocopy) and exposed to use-once proprietary flash bulbs, this melts the impermeable material allowing ink to pass through the screen.
Unfortunately, RISO does not support this printer anymore and the supplies (flash bulbs and screens) can only be obtained third party. These supplies are in dwindling numbers.
The screen has a protective film. The screen is attached to a handstamp (on the right).
Overall the process took me several hours from cutting the original fabric down from a 10 meter bolt (about 394 inches) to about 39-40 inch lengths of cotton fabric. From there the towels were finished with a rotary cutter because my initial scissor cuttings were jagged.
The faito logo was printed from my original design. Placed in the printer. A screen was developed a total of three times. The first time I followed the directions and used the included blue filter which only served to burn the image into the filter rather than the screen. The process was repeated without the filter but this time because I didn’t trim the paper and instead folded it to fit the printer stage, the crease shadows from the folded paper showed up on the screen. Finally, a fresh image was made and cut to size and a second screen was flashed and developed.
The screen was inked, attached to the hand stamp and tested on a sheet of paper. Thankfully, I had a piece of cardboard underneath the paper as the ink leaked through the paper (and also leaked through the fabric). I had to use papers on the cardboard to block the previous ink that seeped through onto the cardboard as it could ruin the underside of the towels with errant ink marks. The screen was also re-inked due to too light prints.
After all the towels were stamped, they were dried over night. Then ironed to set the ink. And then placed in the washer on cold permanent press.
The towels were then removed. Ironed. Loose threads were removed from frayed ends by scissor. Then the towels were re-ironed and folded.
The prints have a weathered and distressed look and can be purchased on the etsy shop.
I had these made as an homage to one of the greatest movie posters of all time, the Endless Summer.
This limited run sold out on the first day of posting them to the Etsy shop. I might look into having [some] more made but might tweak the design a little bit.
So if you have a wheeled bag or carry a lot of stuff in the trunk of your car, it’s sometimes nice to protect the finish. Especially if the car is relatively new.
Up until a few weeks ago, I was using a towel, but I recently came across this bumper protector. It’s basically a soft neoprene mat that drapes over the back of your car. It attaches to carpet via Velcro.
It does the job pretty well. The Velcro, however, does pull on the fibers of the carpet especially if they are weak such as on the model three.
The mat is 29x12in and the perfect width to fit the trunk compartment cover on my model 3.
You can purchase it here >>>> https://www.amazon.com/Boot-Flap-Co-Bumper-Guard/dp/B075LW8WLD
So the GoPro mount turned out to be a better success than I thought.
The problem was trying to convince people to do their regular kendo and not worry about damaging the camera. It’s a GoPro ppl!!!
Some understood and would have happily tsuki-ed me all night long until I had to motion to yamae (I’m talking about you, Simeon and Okura sensei) but others were very timid and ended up just tapping the camera with the tip of the shinai.
The new backpack mount works great as a tsuki mount for GoPro.
It didn’t fall off.
It’s been awhile since I’ve posted a GoPro video.
Previously I used the GoPro vented helmet strap to mount the camera to the tsuki flap. However, the strap has these dangly bits and isn’t very secure.
This last weekend I was browsing Amazon for GoPro mounts and I came across this one:
It’s a velcro strap for backpacks.
The inner surface is textured and supposed to be “anti-slip”.
Here it is wrapped around the tsuki flap with the velcro parts between the flap and the protector beneath the tsuki flap.
Using the included J adaptor, the GoPro can be adjusted to be level.
We’ll see how it goes at practice tomorrow.
So I have this nice roller bag from http://www.planeteclipse.com to fit my oversize bogu (hey what can I say? I’m a big guy).
I put the bogu in the bottom half and gi in the top.
Anyways, this is supposed to be a how-to on fixing a zipper, specifically repairing a retainer/retaining box.
About two years after purchasing this bag, the retainer box and slider fell off. The retainer box is at the end of the zipper and keeps the slider from falling off. The box fell off because there was weakness in the tape.
Basically the part of the tape attached to the box became separated from the rest of the tape and the box fell off.
Amazon sells replacement zipper parts. It is important the parts are sized properly. I purchased this kit.
Rather than replacing the whole zipper tape around the bag which would involve sending the bag to a seamstress, I decided to tape the zipper tape back together with this:
These are vinyl tape patches for repair of synthetic fabrics such as on down jackets, inflatables, rain gear, tents. They are self adhesive and can be cut down to size.
The patch was used to repair the zipper tape. The slider was inserted onto the zipper and then the box was attached to the repaired tape.
The replacement box was slid onto the tape and crimped down with a needle nose plier. It took a great deal of effort to do this since the patch would bunch up in the middle. I had to widen the groove in the box and then pinch it down after. The opposite side of the tape was inserted into the slider and the box.
Well, it seems the fix is only temporary since the adhesive is not strong enough to keep the frayed parts of the zipper intact for long. I’ve already replaced the tape once.
I’ve been wanted to get this journal from
However, I wanted to start journaling right away, so I found this leather journal cover on Amazon that comes with a 3.5×5.5in insert with dotted pages. Replacement notebooks are cheap (you can use field notes, field books or moleskine cahier).
Compared to the Musha shugyo nikki (means “warrior quest/pilgrimage journal”) it is only $14.95 whereas the one from Bujin design is $54 plus VAT and shipping.
It comes with an elastic strap. Somehow you can insert three notebooks but I have yet to figure that out.
Hopefully by journaling I’ll be able to further incorporate what I learned during first and second practice.
Maybe if I get access to a laser cutter I’ll engrave something on the cover.